Date: 10/25/2025

This product has been Discontinued!!! There is no support for this product (PAH60 / PAH60GW).
There have been a few undetermined cases of improper installation/usage which may cause a fire to the unit.

PLEASE REMOVE THIS PRODUCT FROM YOUR BIKE AS SOON AS POSSIBLE. WE HAVE A REPLACEMENT PART THAT YOU CAN ORDER BELOW, MENTION THIS PART AND YOU WILL RECEIVE A DISCOUNT OFF THE NEW PART. ORDER REPLACEMENT PART #LH40GW

By continuing the use of the PAH60 product, the customer acknowledges and agrees that SoCalMotoGear shall bear no liability or responsibility for any direct, indirect, incidental, or consequential damages, losses, or injuries resulting from its installation, operation, or misuse. The customer further acknowledges that while adding an inline fuse may or may not remedy operational problems, undertaking such modifications does not transfer liability to SoCalMotoGear. The customer assumes full and exclusive liability for any property damage, personal injury, or legal non-compliance arising from the product's use or modification. It is the sole responsibility of the customer to ensure proper installation and compliance with all local laws and safety regulations regarding the use of the PAH60.
 Date: 03/25/2025

URGENT PAH60 UPDATE

You may have recently installed the INLINE 40AMP FUSE kit that we sent to all PAH60 customers.

If this fuse is ever blown, please do NOT replace it! Contact us immediately! (service@socalmotogear.com)

This fuse is protecting the internal circuitry and if this fuse is blown, there could be a serious internal failure and should NOT be replaced! Please let anyone you know that owns a PAH60 about this message.It is safe to continue to use the PAH60 with the Inline Fuse kit (P/N: ILF40A) connected.

PAH60 ILF40A Inline Fuse

If you are a PAH60 customer and have not received an inline fuse kit (ILF40A) yet, please email to request one free of charge with your PAH60 order number/proof of purchase : service@socalmotogear.com

Date: 10/10/2024

INLINE FUSE KIT - UPDATE TO PAH60

Models: PAH60GW / PAH60GX / PAH60UN

If you have not already disconnected the power cable from the PAH60 to the battery, please do so immediately as a precaution. If you know someone who has this product installed, please notify them as well.

LATEST UPDATE: KITS NOW SHIPPING!

We had a production delay but are happy to now report that the INLINE FUSE KITS started shipping out this week. Some of you may have already received it. For those who have yet to receive the kit, please be on the lookout for your package coming soon.

Inline Fuse Kit

No receipt is necessary for this kit as long as you have a PAH60 installed on your bike!

This will be a 10AWG inline 40 Amp fuse kit to be installed on the "RED" power cable from the PAH60 that connects to the battery. This kit does not require soldering.

Alternatively, if you are unable to wait and are comfortable with soldering/crimping, you can obtain similar parts at the local auto parts/electronics store. The cable must be 10AWG and the fuse rated at 40 amps. The fuse would need to be installed closer to the battery side. 3-4 inches of heat shrink tubing is necessary to protect the added wiring for both options below:

  • HEAT SHRINK: 3-4 inches of heat shrink tubing is necessary to protect the added wiring.
  • ELECTRICAL TAPE over heat shrink tube: If a heat gun is not available, you can use electrical tape to wrap over the heat shrink tubing. Heat shrink tubing should be placed over the new connection, then carefully wrap with electrical tape. Be sure to wrap starting from the cable going across the entire connection and the heat shrink wrap, and back onto the cable.

These two alternatives are strictly for those who cannot wait to receive the updated inline fuse kit.

The INLINE FUSE KIT will begin shipping out in approximately 1-2 weeks.

In the meantime, the PAH60 unit should be disconnected from the battery.

Action to be Taken:

If you haven’t already emailed us with your contact information, please do so on this form.

Enter your "SHIP TO address" in the Comments/Questions field below in order to receive the kit.

Contact Us